MOON EVOLUTION SERIES
i-7 Dual-Mono Integrated Amplifier


  MOON i-7 Dual-mono Integrated Amplifier
 



The MOON i-7 integrated amplifier is a dual-mono fully balanced differential design, representing the next generation of MOON high-performance audio components. Using our new proprietary "Lynx" amplification circuit, the i-7 produces a high-current rock-solid 150 watts per channel into 8 ohms with absolutely no sonic colorations. A genuine non-compromising solution for those who don't require separate component systems, this integrated provides for astounding ease-of-use as a result of a variety of programmable features. Further raising the bar, the MOON i-7 can be fully integrated into a custom-install environment via an RS-232 port. As well, a plethora of user selectable cosmetic options are available at the time of purchase.



"Celebrating 25 Years Of Excellence"

 


 
Significant Design Features

Full unsolicited RS-232 bidirectional feedback · Lynx circuitry which is a "no overall feedback" design resulting in real-time amplification, a more accurate musical reproduction with respect to tonality, virtually non-existent intermodulation distortion and the elimination of common phase errors resulting from feedback · Custom proprietary toroidal transformer design with lower magnetic, electrical and thermal loss, yielding an improved power transfer and lower regulation factor. The result is increased current speed and better dynamics · An oversized dual-mono power supply · SimLink controller port allows for 2-way communications between other compatible MOON Evolution Series components · M-eVOL volume control circuit based on a resistive array configuration with no sonic degradation of the audio signal regardless of the selected volume setting · M-Lock circuit for “user selectable” maximum volume setting lock-out for each line input · Individual “gain offset” for each individual line input with a ±10dB range · Each line input is fully configurable to be “home-theater ready”, where the gain section of the i-7 is bypassed · 130 individual volume steps in 1dB and 0.5dB increments · An exceptionally short signal path , yielding a much faster transient response · 12 Volt trigger output for remote operations · "Class A" output to 5 watts for greater efficiency · Four-layer PCB tracings with dedicated ground and power planes. The advantages include better ground and power supply circuit layouts resulting in a much shorter signal path and a vastly improved signal-to-noise ratio · Ultra rigid chassis construction to minimize the effects of external vibrations · Accurate matching of the very finest quality electronic components in a symmetrical circuit design · Improved reliabilty through the elimination of moving parts · Low operating temperature for a longer than normal life expectancy.













 



  Specifications:

 
Type Solid State
Configuration Dual-Mono / Balanced
Power Supply Transformer 2 x 0.5kVA
Power Supply Capacitance 66,800µF
Class of operation - Amplifier A/AB
Single Ended Inputs   (RCA) 5 pairs
Balanced Inputs   (XLR) 1 pair
Input Sensitivity 490mV - 6.0V RMS
Input Impedance 23,700 ohms
Monitor Loop 1
Preamplifier Output 1 pair @ 50 ohms   (RCA)
Output Device Types - Amplifier Bipolars - 6 per channel
Output Binding Posts Gold-plated WBT
Output Power @ 8 ohms 150 Watts per channel
Output Power @ 4 ohms 250 Watts per channel
Output Impedance 0.02 ohms
Damping Factor > 400
Volume Steps 1.0dB from 0-30 and 0.5dB from 30-80
Gain Control M-eVOL   (Resistive Array)
Gain 37dB
Signal-to-noise Ratio - Preamplifier 114dB   (20Hz-20kHz)
Signal-to-noise Ratio - Amplifier 100dB @ full power
Maximum Output Voltage 45 Volts
Slew Rate 35V/µs
Maximum Current - Peak 40 amperes
Maximum Current - Continuous 20 amperes
Frequency Response 10Hz - 100kHz   (+0/-3dB)
Crosstalk @ 1kHz -100dB
IMD unmeasurable
THD   (20Hz - 20kHz @ 1 watt) < 0.02%
THD   (20Hz - 20kHz @ 150 watts) < 0.05%
 
12 Volt Trigger Output Operation
 
 
 
Direct Logic   (0V = off, 12V=on)   using
a 3.5mm mono microphone jack with an
output impedance of 1000 ohms and current
requirement of 12mA
SimLink Port 1 input + 1 output each on 1/8" mini-jack
RS-232 Port 9-pin female DB connector
IR input 1/8" mini-jack
 
Remote Control All-Aluminum Full Function
Display Type 8 character dot matrix LED
Power Consumption @ idle 50 Watts
AC Power Requirements 120V / 60Hz     240V / 50Hz
Fuse Replacement - 120V 6.0A long fast blow
Fuse Replacement - 230V 3.0 long fast blow
Shipping weight 58 lbs / 26 kgs
Dimensions   (w x h x d) 18.75 x 5.5 x 16.5 in.
 
Preliminary specifications - subject to change without notice.
 


Close this window                             Print this page